In this example, I have specified a static IP address, a subnet mask, a gateway, and several DNS servers. Enable automatic interface boot:

ONBOOT=”yes”

After you have made the changes, restart your network service. If it is OK, you will see the following listing:

# service network restart

Restarting network (via systemctl): [ OK ]

Also, you may just reload all connection profiles:

# nmcli connection reload

How to Get a Dynamic IP Address from DHCP?

If you server must get a dynamic IP address from the DHCP server on your network, open the interface configuration file and change the settings:

We have removed all parameters related to the IP addresses and mask, and changed the way of how the IP address is assigned to dhcp?(BOOTPROTO=”dhcp”). After making all changes, don’t forget to reload the network service.

How to Disable IPv6 on RHEL/CentOS?

By the time the article had been written,?ipv6?was not actively, and often administrators prefer using ipv4, if possible. So if you are not using the IPv6 protocol, disable it on your server. If you are sure that neither of your services is configured to work with ipv6, you can proceed to network interface configuration. Otherwise, it is better to start with a check. You need to check which services are using IPv6 and disable the protocol in the service config. Run this command:

# netstat -tulnp

I have a test server, so?ipv6?is used only for sshd and chronyd. It may be detected by “:::”.

To prevent problems after disabling ipv6 in the network configuration, disable the protocol for the services that use them on your server. For example, open the sshd configuration file:

# mcedit /etc/ssh/sshd_config

And uncomment these lines:

#AddressFamily any
#ListenAddress 0.0.0.0

Then restart the service:

# service sshd restart

As you can see,?ipv6?is not available for sshd now. Do the same for other services.

Let’s disable ipv6 protocol in the network settings. Open?/etc/sysctl.conf:

# nano /etc/sysctl.conf?
And add the following lines there:

net.ipv6.conf.all.disable_ipv6 = 1
net.ipv6.conf.default.disable_ipv6 = 1

Save the file and apply the changes using:

# sysctl -p

net.ipv6.conf.all.disable_ipv6 = 1
net.ipv6.conf.default.disable_ipv6 = 1

Then open?/etc/sysconfig/network. Add this configuration to it:

NETWORKING_IPV6=no
IPV6INIT=no

Remove the following line from the network configuration interface file?/etc/sysconfig/network-scripts/ifcfg-eth0:

IPV6INIT="yes"

And finally, disallow the use of ipv6 in grub:

# nano /etc/default/grub

Add the following to the end of GRUB_CMDLINE_LINUX line:

ipv6.disable=1

After making all changes, save the file and update grub:

# grub2-mkconfig -o /boot/grub2/grub.cfg

Reboot your server and check your network configuration:

# ifconfig
The?ipv6?protocol is disabled on your server.

Setting DNS Namesservers on CentOS/RHEL

You can configure DNS nameservers for your host using?/etc/resolv.conf?or specify them in your network interface settings. When setting up static configuration for the Linux network interface, we have already specified the DNS servers using the following parameters:

DNS1=
DNS2=
DNS3=

Set the DNS servers you need and restart the network service.

DNS nameservers are automatically registered in?/etc/resolv.conf taking them from the network configuration file. If you didn’t specify DNS servers during network configuration, do it manually in?/etc/resolv.conf:

nameserver 1.1.1.1
nameserver 8.8.8.8
nameserver 8.8.4.4

Create Multiple IP Addresses to Single Network Interface on RHEL/CentOS

If you want to use multiple IP addresses in your network interface, you can configure it through the interface alias or add an additional IP address to the main configuration file.

# nano /etc/sysconfig/network-scripts/ifcfg-eth0

Change it like this:

# Generated by parse-kickstart
UUID="b8bccd4c-fb1b-4d36-9d45-044c7c0194eb"
IPADDR1="*.*.*.*"
IPADDR2="*.*.*.*"
GATEWAY="*.*.*.*"
NETMASK="255.255.255.0"
BOOTPROTO="static"
DEVICE="eth0"
ONBOOT="yes"
DNS1=1.1.1.1
DNS2=8.8.8.8
DNS3=8.8.4.4

Where:
IPADDR1 – the first IP address
IPADDR2 – the second IP address
GATEWAY – the main gateway

Or create an?alias?to your main configuration file:

# nano /etc/sysconfig/network-scripts/ifcfg-eth0:1

And add some lines here, but do not specify the gateway:

After configuration of all settings, restart your network service:

# service network restart

Configure VLAN (802.1Q) Tagging on RHEL/CentOS

We told more about configuration of multiple VLANs for a network interface in CentOS/RHEL/Fedora in the article: How To Configure 802.1Q VLAN Tagging on RHEL/CentOS Linux.

Configuring Multiple Network Interfaces on RHEL/CentOS

If you have several network interfaces on your server, you can specify different IP addresses for them. Let’s learn how to do it. If you have more than one network interface on your server, the “ip a” command should display this information:

# ip a

1: lo: <LOOPBACK,UP,LOWER_UP> mtu 65536 qdisc noqueue state UNKNOWN group default qlen 1000
link/loopback 00:00:00:00:00:00 brd 00:00:00:00:00:00
inet 127.0.0.1/8 scope host lo
valid_lft forever preferred_lft forever
2: eth0: <BROADCAST,MULTICAST,UP,LOWER_UP> mtu 1500 qdisc pfifo_fast state UP group default qlen 1000
link/ether 52:52:42:54:2c:36 brd ff:ff:ff:ff:ff:ff
inet 15.*.*.*/16 brd 15.*.*.255 scope global eth0
valid_lft forever preferred_lft forever
3: eth1: <BROADCAST,MULTICAST> mtu 1500 qdisc noop state DOWN group default qlen 1000
link/ether 52:52:42:54:2c:b8 brd ff:ff:ff:ff:ff:f

To configure the second interface, create a file for it:
# nano /etc/sysconfig/network-scripts/ifcfg-eth1
And add the following configuration to it:

IPADDR="*.*.*.*"
GATEWAY="*.*.*.*"
NETMASK="255.255.255.0"
BOOTPROTO="static"
DEVICE="eth1"
ONBOOT="yes"

Then you must set a default gateway on your server. Check which gateway is set now and change it if necessary:

# netstat -nr

Kernel IP routing table
Destination Gateway Genmask Flags MSS Window irtt Iface
0.0.0.0 15.*.*.1 0.0.0.0 UG 0 0 0 eth1
169.254.0.0 0.0.0.0 255.255.0.0 U 0 0 0 eth0
169.254.0.0 0.0.0.0 255.255.0.0 U 0 0 0 eth1
15.*.0.0 0.0.0.0 255.255.0.0 U 0 0 0 eth0
15.*.*.0 0.0.0.0 255.255.255.0 U 0 0 0 eth1

The eth1 interface is the main gateway. I want to use eth0. Let’s change it:

# route add default gw *.*.*.*?– replace the gateway with the one specified in eth0

# route delete default gw *.*.*.*?— remove the eth1 gateway

If you want to keep this setting after the server reboot, add these commands to?rc.local?(see the article How to Start Services Automatically on Boot on RHEL/CentOS?).

Useful Networking Commands on RHEL/CentOS

• ifdown eth1?— disables the specified network interface
• ifup eth1?– enables the specified network interface
• ifconfig?– shows the information about all network interfaces
• ifconfig -a | grep ether | gawk '{print $2}'?— is a command to display MAC addresses of an interface
• ip a | grep ether | gawk '{print $2}'?— the same as above using ip a
• service network restart?or?systemctl restart network?– restarts network service using systemctl
• systemctl restart NetworkManager.service?– restarts NM
• ip route?or?ip route show?— displays the routing table on Linux
• ping host?– pings the specified host
• whois domain?– shows whois info about a domain
• dig domain?– shows DNS information about a domain

Network Administration Tools on RHEL/CentOS

If a server has been working for some time or it has not been configured by you, the first thing you should do is to learn what interfaces are there on the server. To make it more convenient, install the necessary tools from the basic repository:

# yum install net-tools -y

After the installation, you can use?ifconfig:

# ifconfig

eth0: flags=4163<UP,BROADCAST,RUNNING,MULTICAST> mtu 1500
inet 15.*.*.* netmask 255.255.255.0 broadcast 185.*.*.255

As you can see, the name of our network interface is?eth0.

If you have not installed?net-tools, you can view your interfaces using the following command:

# ip a

The output will be almost the same.

Network Management Using NetworkManager in CentOS/RHEL 8

On RHEL/CentOS 8 it is recommended to use only NetworkManager for network configuration. This service manages network connections, controls settings and applies changes to network adapters.

To check NM status, use this command:

# systemctl status NetworkManager.service

CentOS offers to use the command console?nmcli?or a graphic tool?nmtui to configure a network.

To go to the network configuration mode, enter this command:

# nmtui

After selecting the first item, you will see a window to choose the network interface to edit:

Select an interface and edit it:

You can edit a device name, an IP address, a gateway and DNS servers. Also, you can change the way to assign an IP address to DHCP in the NM interactive menu:

Change “manual” to “automatic”:

Then save the changes. Using nmtui you can do the same configuration tasks in the graphical mode like you do in the configuration files. If you prefer using the command prompt to configure interfaces, you can use nmcli. For example, the following commands will change an IP address, a gateway and DNS servers for eth1.

# nmcli con mod eth1 ipv4.addresses 192.168.11.24/24
# nmcli con mod eth1 ipv4.gateway 192.168.11.1
# nmcli con mod eth1 ipv4.dns "8.8.4.4"

To apply the changes, restart the interface:

# nmcli con up eth1

If it is more convenient for you to work with the configuration files, install a special package?network-scripts?(by default, CentOS 8 does not have it) using yum.

# yum install network-scripts -y

Upgraded:
initscripts-10.00.1-1.el8_0.1.x86_64
Installed:
network-scripts-10.00.1-1.el8_0.1.x86_64 network-scripts-team-1.27-10.el8.x86_64
Complete!

After the installation, you can edit network settings in the configuration files as described earlier.